Home / Guides / 1x gravel chainring size
1x gravel chainring size: 40T vs 42T vs 44T
Gears on 10-44, 10-46 and 10-51, and what fits.
At a glance
Short answer: Start with 40T if you climb a lot or carry bags, 42T for mixed riding, and 44T if you ride fast and keep running out of gears. Each 2-tooth step makes every gear about 5% harder. On Shimano's 10-51, a 44T still climbs like a 40T on SRAM's 10-46.
Who it's for: riders buying a 1x gravel bike or a new chainring for one, on Shimano GRX 12-speed or SRAM XPLR.
For your own tire and cassette, use our gear calculator and its compare view.
The words, quickly
A 1x ("one-by") bike has one chainring at the front and no front derailleur. The chainring is the toothed ring on the crank; 40T means 40 teeth. The cassette is the stack of cogs on the rear wheel; 10-51 means its smallest cog has 10 teeth and its largest 51. The ratio is chainring teeth divided by cog teeth: lower is easier.
Your hardest gear depends only on the ring
All four cassettes start at 10 teeth. Figures use 700x40 mm tires at 90 rpm, a steady, normal pedalling speed.
| Ring | Hardest gear | Ratio | Speed at 90 rpm |
|---|---|---|---|
| 40T | 40x10 | 4.00 | 47.6 km/h (29.6 mph) |
| 42T | 42x10 | 4.20 | 50.0 km/h (31.1 mph) |
| 44T | 44x10 | 4.40 | 52.4 km/h (32.6 mph) |
Going up 2 teeth adds about 2.4 km/h before you have to spin faster than 90 rpm. You can, of course, spin faster. Most of us just don't enjoy it for long.
Your easiest gear depends on both
Lowest ratio and speed at 90 rpm, 700x40 mm. 10-44 is SRAM XPLR 12-speed, 10-45 and 10-51 are Shimano, 10-46 is SRAM XPLR 13-speed:
| Ring | 10-44 | 10-45 | 10-46 | 10-51 |
|---|---|---|---|---|
| 40T | 0.91, 10.8 km/h | 0.89, 10.6 km/h | 0.87, 10.4 km/h | 0.78, 9.3 km/h |
| 42T | 0.95, 11.4 km/h | 0.93, 11.1 km/h | 0.91, 10.9 km/h | 0.82, 9.8 km/h |
| 44T | 1.00, 11.9 km/h | 0.98, 11.6 km/h | 0.96, 11.4 km/h | 0.86, 10.3 km/h |
What that means on the bike:
- 2 teeth is about 5%. 40 to 42 is 5.0% harder in every gear, 42 to 44 is 4.8%. That is less than one rear shift on any of these cassettes.
- The 10-51 buys you a bigger ring. A 44T on 10-51 (0.86) climbs like a 40T on 10-46 (0.87) and tops out 4.8 km/h higher.
- Compared with a 2x. A 44T with 10-51 lands close to a 48/31 double with an 11-36 cassette (0.86 at the bottom, 4.36 at the top on the same tire). Our 46/30 vs 48/31 guide has the 2x numbers.
- The catch is bigger jumps. On the 10-51, neighbouring cogs are 13% to 20% apart. On SRAM's 13-speed 10-46, the first three shifts from the 10T cog are 8% to 10% apart.
Which ring for which rider
| If you... | Try | Why (gearing) |
|---|---|---|
| Ride steep climbs, carry bags or ride long and slow | 40T (or 38T) | Lowest gears in the table above |
| Ride rolling gravel with some tarmac | 42T | 5% more top end than 40T; lowest ratio stays under 1.0 on every cassette here |
| Race, ride in fast groups, or spin out on descents | 44T | 52.4 km/h at 90 rpm in the top gear |
| Want a 44T but also low climbing gears | 44T with 10-51 | Lowest gear 0.86, close to 40T on SRAM's 10-46 |
Shimano's own gravel gearing guide describes its choices this way: "42T – Higher speed on faster roads, best for racers and cyclocross riders transitioning to gravel." "40T – Balanced climb and speed for rolling terrain and long gradual ascents or those who prefer a higher cadence when riding." "38T – For maximizing low climbing gears, especially for those who live in mountainous terrain or carry camping gear on multi-day rides."
If you never use your hardest gear today, a bigger ring mostly makes your climbs harder.
What fits your groupset
The freehub body is the part of the rear hub the cassette slides onto, and it must match the cassette.
| Groupset | Rings the maker lists | Cassettes | Rear derailleur | Freehub body |
|---|---|---|---|---|
| Shimano GRX RX820 1x12 (mechanical and Di2) | FC-RX820-1: 40, 42, 44, 46T | 10-45 or 10-51 (Di2: 10-51) | RD-RX822-GS (45T only), RD-RX822-SGS or Di2 RD-RX827-SGS (51T only) | MICRO SPLINE |
| Shimano GRX RX610 / RX717 1x12 | FC-RX610-1: 38, 40T | 10-45 or 10-51 (RX717 Di2: 10-51) | Same RX822 pair, or Di2 RD-RX717-SGS (51T only) | MICRO SPLINE |
| SRAM XPLR eTap AXS and Apex XPLR AXS, 12-speed | Direct mount rings 38 to 46T, plus 48 and 50T aero rings (Apex 1 Wide crank: 40, 42T) | 10-44 (XG-1271, XG-1251), 11-44 (PG-1231) | XPLR 12-speed, 44T max | XDR for 10-44; 11-speed road body for 11-44 |
| SRAM RED, Force, Rival XPLR AXS, 13-speed | Rival XPLR crank: 38, 40, 42, 44, 46T | 10-46 only | XPLR 13-speed, Full Mount | XDR |
Notes that change what you buy:
- Shimano's derailleur follows the cassette, not the ring. RD-RX822-GS lists 45T as both the minimum and maximum largest cog, and RD-RX822-SGS does the same at 51T. Changing ring size doesn't change the derailleur.
- Shimano also lists an HG road option. The RX820 and RX610 1x lineups include RD-RX820 with 11-34 or 11-36 road cassettes. That keeps a road freehub but gives a much narrower range. Our GRX 12-speed compatibility guide covers it.
- SRAM's two generations don't mix. SRAM's compatibility FAQ says: "The Rival, Force and Red E1 XPLR AXS rear derailleurs are 13-speed components and only intended to work with our 10-46T 13-speed cassettes." The 12-speed XPLR derailleurs take 10-36, 10-44 and 11-44 instead.
- SRAM 13-speed derailleurs are Full Mount. They mount without a derailleur hanger, and the RED XPLR AXS page says: "Requires frame with UDH interface". Check yours in our UDH and Full Mount frames guide.
Before you swap a ring
- Check the ring exists for your crank. SRAM's RED XPLR crank page says: "Non-aero direct mount chainrings from 38T to 46T can be swapped with a single tool". SRAM's XPLR crank spec tables list both 12 and 13 speeds. Shimano's US product page lists replacement 40T and 42T rings for FC-RX820-1, but not 44T or 46T, so ask a dealer before a ring-only swap to those sizes.
- Check your chainstay on SRAM. Its XPLR crank pages say: "Use with XPLR derailleurs on bikes with chainstay lengths down to 415 mm. Road cranksets should be used with chainstay lengths 414mm and below". The chainstay is the frame tube from the crank to the rear axle.
- Re-check chain length. A bigger ring can need a longer chain. The chain length calculator covers GRX 1x; for SRAM 13-speed Full Mount it points you to SRAM's own chart.
- Total capacity is the cassette's job on 1x. 10-51 is a 41-tooth spread, exactly RD-RX822-SGS's 41T total capacity. Our derailleur capacity checker does the sum for the derailleurs it lists.
Related on Pedal Brief
- Gear ratio calculator
- 46/30 vs 48/31 gravel chainrings
- Shimano GRX 12-speed compatibility
- Derailleur capacity checker
- Chain length calculator
- Road and gravel groupsets 2026
Sources and notes
Where the sources disagree
- Which rings go with GRX 1x12 Di2. Shimano's story "A Guide to SHIMANO 1x and 2x Gearing Setups for Gravel" says: "Shimano’s GRX 1x12-speed Di2 uses a 10–51T cassette paired with a single chainring (40T or 42T) for customizable range and step sizes." Its chainring list then adds 38T. Shimano's productinfo lineups list FC-RX820-1 at "46T/44T/42T/40T" for RX820 1x12 Di2 and FC-RX610-1 at "40T/38T" for RX717 1x12 Di2. The table uses the lineups.
- 11-51 vs 10-51. The same story's speed example says: "For a 1x12-speed setup using GRX 42T chainring and an 11-51T cassette, a rider pedaling at 100 RPM will travel at the following speeds when in the smallest three cogs on the cassette:" It then lists a 10T cog. Every Shimano 51T cassette spec chart we read (CS-M8100-12, CS-M7100-12, CS-M8200-12, CS-M7200-12) says 10-51T. We use 10-51.
- RED XPLR chainring sizes. SRAM's own pages do not agree. The crankset features say non-aero rings from 38T to 46T and aero rings from 44T to 50T. The same page's spec table lists 40T to 50T and omits 38T. The RED XPLR gearing FAQ lists 38T to 46T, plus aero rings in 48T, 50T and 52T. The direct mount ring FAQ lists 38T to 46T plus 48T and 50T aero rings, with no 52T. All four lists include 40T to 46T, which is all this guide needs. The table's 12-speed row follows the direct mount ring FAQ. We left 52T out.
- Force XPLR chainring sizes. The Force XPLR crankset description says it is offered in 38T to 46T standard rings and 44T to 50T aero rings. The same page's spec table lists 42T, 44T, 46T, 48T and 50T, so 38T and 40T are missing. The table uses the Rival XPLR crank, whose description and spec table agree (38T to 46T).
What we could not confirm
- 44T and 46T replacement rings for FC-RX820-1. Shimano's en-NA product page lists "Chainring 42T for FC-RX820-1" and "Chainring 40T for FC-RX820-1" as replacement parts, but no 44T or 46T, although the spec chart lists all four sizes. Ask a dealer before planning a ring-only swap to 44T.
- A maximum chainring for the GRX 1x derailleurs. The RD-RX822-GS, RD-RX822-SGS and RD-RX827-SGS spec charts show "-" or "0T" for front difference and no chainring limit. We used the crank charts' ring lists.
- US prices. Shimano's productinfo pages show no price. From the box, SRAM's model pages displayed euro MSRPs only (for example XG-1371 €300 and XG-1271 €237 on 14 Nov), so no price is in the body.
- Shimano's and Wolf Tooth's speed examples. Shimano gives speeds at 100 rpm without a tire size; Wolf Tooth's 100 rpm figures use a 650b x 2.2 tire. Neither is compared with our 700x40 figures.
Method and caveats
- Gear figures come from our gear calculator's code (
gear-calculator.js): ratio = ring / cog, wheel rollout = pi x (622 + 2 x tire width) mm, speed = rollout x ratio x 90 rpm. Tire 700x40 mm. On 700x45 every speed rises about 1.4%. - Cog lists: 10-44 from SRAM XG-1271 (10, 11, 13, 15, 17, 19, 21, 24, 28, 32, 38, 44); 10-45 from Shimano CS-M8100-12 (10-12-14-16-18-21-24-28-32-36-40-45); 10-46 from SRAM XG-1391, XG-1371 and XG-1351 (10, 11, 12, 13, 15, 17, 19, 21, 24, 28, 32, 38, 46); 10-51 from Shimano CS-M8100-12 (10-12-14-16-18-21-24-28-33-39-45-51).
- SRAM's 11-44 (PG-1231) is not in the gear tables. With its 11T top cog, every hardest-gear figure is about 9% lower than with a 10T cog.
- Percentages are ratio differences. The 2x comparison uses the same calculator figures as our 46/30 vs 48/31 guide (48/31 with 11-36, 700x40).
Spot an error? Email [email protected].
Sources
- Shimano productinfo spec charts: FC-RX820-1, FC-RX610-1, RD-RX822-GS, RD-RX822-SGS, RD-RX827-SGS, RD-RX717-SGS, RD-RX820, CS-M8100-12, CS-M7100-12, CS-M8200-12, CS-M7200-12
- Shimano lineups: GRX RX820 1x12, GRX RX820 1x12 Di2, GRX RX610 1x12, GRX RX717 1x12 Di2
- Shimano product pages: FC-RX820-1, FC-RX610-1
- Shimano: A Guide to SHIMANO 1x and 2x Gearing Setups for Gravel
- SRAM cassettes: XG-1271, XG-1251, PG-1231, XG-1391, XG-1371, XG-1351
- SRAM cranksets: RED XPLR, Force XPLR, Rival XPLR, Apex 1 Wide
- SRAM rear derailleurs: RED XPLR AXS, Force XPLR AXS, Rival XPLR AXS, Apex XPLR AXS, Force XPLR eTap AXS (12-speed, service page)
- SRAM support: RED XPLR AXS gearing options, Direct mount XPLR chainring sizes, XPLR eTap AXS compatibility, RED XPLR AXS FAQ section
- Wolf Tooth: 1X Gravel and Adventure-Road Setup
Disclosure: Pedal Brief may earn a commission if you buy through links on this page, at no extra cost to you. This version has no affiliate links. We have not ridden these setups back to back. Specs come from Shimano and SRAM; gear figures are our own arithmetic from the tooth counts. Full disclosures.